Seagate ST3655N Handbuch Seite 31
- Seite / 151
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2.8.2 Passive termination
All interface signals with the drive are single-ended and must be termi-
nated with 220 ohms to +5V and 330 ohms to ground at each end of the
cable. All signals use open-collector drivers or three-state drivers. The
Seagate part number for the 220/330-ohm terminator is 75916526-9.
Single-ended SCSI devices providing termination power have the follow-
ing characteristics:
Terminator voltage (V) 4.0 to 5.25
Source drive capability (mA, min) 800
Line driver
(transmitter or transceiver)
+2.85V
110
ohms
+2.85V
110
ohms
Flat cable pair
Line receiver
ANSI SCSI
compatible
circuit
ANSI SCSI
compatible circuit
Figure 4. Active termination
Line driver
(transmitter or transceiver)
+5V
220
ohms
330
ohms
+5V
220
ohms
330
ohms
Flat cable pair
Line receiver
ANSI SCSI
compatible
circuit
ANSI SCSI
compatible circuit
Figure 5. Passive termination
ST3655 Family SCSI Drives Product Manual, Rev. A 21
- ST3655 Family: 1
- ST3285N, ST3390N 1
- ST3550N, ST3655N 1
- SCSI Interface Drives 1
- Product Manual 1
- Contents 5
- 1.0 Specifications summary 11
- 1.3 Functional specifications 12
- 1.4 Physical dimensions 12
- 1.5 Reliability 12
- 1.6 Acoustics 13
- 1.7 Seek time 13
- 1.7.2 Thermal compensation 13
- 1.8 Environmental 14
- 1.8.1 Ambient temperature 14
- 1.8.2 Temperature gradient 14
- 1.8.3 Relative humidity 14
- 1.8.4 Altitude 14
- 1.9 Shock and vibration 15
- 1.10 Start and stop time 15
- 1.10.1 Power-up sequence 15
- 1.10.2 Power-down sequence 16
- 1.10.3 Auto-park 16
- 1.11 DC power 17
- 1.11.1 Input noise 17
- 1.11.2 Power management 17
- 1.11.3 Power consumption 18
- 1.12 Agency listings 20
- 1.13 FCC verification 20
- Sicherheitsanleitung 21
- 2.0 Hardware and interface 23
- 2.3 Hot-plugging 24
- 2.4 SCSI connector 25
- Figure 3. Drive connector 27
- 2.5 Cable requirements 29
- 2.6 Single-ended cable 29
- 2.7 DC power connector 30
- 2.8 Terminators 30
- 2.8.1 Active termination 30
- 2.8.2 Passive termination 31
- 2.9.2 Start/stop option 33
- 2.9.3 SCSI address 33
- Terminating 34
- Circuit board 35
- 2.10 Remote LED connection 36
- Spindle clock 37
- Internal index 37
- 2.12 Drive mounting 38
- 2.12.1 Bottom mounting holes 38
- 2.12.2 Side mounting holes 38
- Interface 39
- 4.02 (102.11) max 40
- 3.0 Command set 41
- 3.2 Status byte codes 42
- 3.3 Supported commands 43
- 3.4 Group 0 commands 44
- 3.4.2 Rezero Unit command (01 44
- 3.4.4 Format Unit command (04 46
- 3.4.4.1 Types of defects 47
- defect list length 53
- 3.4.6 Read command (08 54
- 3.4.7 Write command (0A 55
- 3.4.8 Seek command (0B 56
- 3.4.9 Inquiry command (12 57
- 3.4.11 Reserve command (16 61
- 3.4.12 Release command (17 62
- 3.4.13 Mode Sense command (1A 63
- 3.4.13.2 Mode sense data 66
- self test 70
- Dev OfL (device off line) 70
- UnitOfL (unit off line) 70
- 3.5 Group 1 commands 71
- 3.5.1.1 Read Capacity data 72
- DPO (disable page out) 73
- (forced unit access) 73
- transfer length 75
- BYT CHK (byte check) 76
- transfer length 76
- 3.5.6 Verify command (2F 77
- 3.5.7.1 Defect list header 79
- 6–8 Parameter list length 80
- 3.5.9 Read Buffer command (3C 81
- 3.5.9.1 Read Buffer header 82
- 3.5.10 Read Long command (3E 83
- 3.5.11 Write Long command (3F 84
- 3.6 Group 2, 3 and 4 commands 85
- 3.7 Group 5 and 6 commands 85
- 3.8 Group 7 commands 85
- A.1 Single-byte messages 87
- REQ/ACK offset 88
- Appendix B. Sense data 89
- B.2 Sense key 91
- Appendix C. Mode pages 99
- C.1 Error Recovery page (01 101
- C.3 Format Device page (03 105
- alternate tracks per zon 106
- Hard Sectoring (HSEC) 108
- Removable Media (RMB) 108
- Surface Map (SURF) 108
- Soft Sectoring (SSEC) 108
- C.5 Caching page (08 111
- Disable Read-Ahead (DRA) 115
- C.6 Control Mode page (0A 116
- C.7 Notch page (0C 118
- C.8 Cache Control page (38 120
- C.9 Soft ID Page (EEPROM) (3C 122
- param enable 123
- Appendix D. Inquiry data 125
- D.2 Vital product data pages 128
- EEPROM image number 131
- D.2.4 Date Code page (C1 132
- Appendix E. Timing diagrams 133
- Reselect identify message to 143
- data (media) 143
- T16 Command dependent 143
- Seagate Technology, Inc 151
Verwandte Produkte und Handbücher für Vernetzung Seagate ST3655N
Vernetzung Seagate Mirra Betriebsanleitung
(20 Seiten)
(20 Seiten)
Vernetzung Seagate GoFlex Net Betriebsanweisung
(11 Seiten)
(11 Seiten)
Vernetzung Seagate GoFlex Home Betriebsanweisung
(95 Seiten)
(95 Seiten)
Vernetzung Seagate Mirra Einstellungsanleitung
(149 Seiten)
(149 Seiten)
Vernetzung Seagate Mirra Einstellungsanleitung
(163 Seiten)
(163 Seiten)
Vernetzung Seagate ST32430N/ND Spezifikationen
(144 Seiten)
(144 Seiten)
Vernetzung Seagate GoFlex Home Betriebsanweisung
(51 Seiten)
(51 Seiten)
Vernetzung Seagate ST32430N Spezifikationen
(154 Seiten)
(154 Seiten)
Vernetzung Seagate ST446452W Betriebsanweisung
(122 Seiten)
(122 Seiten)
Vernetzung Seagate STAM3000100 Betriebsanweisung
(82 Seiten)
(82 Seiten)
(26 Seiten)
Vernetzung Seagate ST3390N Installationsanleitung
(468 Seiten)
(468 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.108 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern