Seagate ST1.2 - Series 8 GB Removable Hard Drive Handbuch Seite 1

Product ManualST1.3 Series100409345Rev. DSeptember 2007ST612712DEGST612712DEST610712DEGST610712DEST680712DEGST680712DEST660712DEGST660712DE

4ST1.3 Series Product Manual, Rev. DRead/write power (typical 3.3V) 230/240 mAPerformance idle mode (typical 3.3V) 140 mALow power idle mode (typical

ST1.3 Series Product Manual, Rev. D52.2 Formatted capacity 2.3 Default logical geometryLBA modeWhen addressing these drives in LBA mode, all blocks

6ST1.3 Series Product Manual, Rev. D2.4 Recording and interface technology2.5 Physical characteristics 2.6 Time to readyTechnology SpecificationInter

ST1.3 Series Product Manual, Rev. D72.7 Power specificationsThe drive receives DC power (+3.3V) through the ZIF (IDE interface) connector for ST61271

8ST1.3 Series Product Manual, Rev. D*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which ma

ST1.3 Series Product Manual, Rev. D92.7.2 Conducted noiseInput noise ripple is measured at the host system power supply across an equivalent 15-ohm re

10ST1.3 Series Product Manual, Rev. D2.7.4 Power-management modesThe drive provides programmable power management to provide greater energy efficiency

ST1.3 Series Product Manual, Rev. D112.8 Environmental specifications2.8.1 Ambient temperatureAmbient temperature is defined as the temperature of the

12ST1.3 Series Product Manual, Rev. D2.8.5 ShockAll shock measurements in this section are carried out at drive level. For all linear shock test, oper

ST1.3 Series Product Manual, Rev. D132.8.6.1 Operating sweep sine vibrationThe following lists the maximum operating sweep sine vibration levels that

Copyright © 2006 - 2007 Seagate Technology LLC. All rights reserved. Printed in U.S.A.Publication number: 100409345, Rev. D September 2007Seagate, Sea

14ST1.3 Series Product Manual, Rev. D2.8.6.4 Nonoperating random vibrationThe test consists of 15 minutes of random vibration using the power spectral

ST1.3 Series Product Manual, Rev. D152.9 AcousticsDrive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). Disc

16ST1.3 Series Product Manual, Rev. D2.11 ReliabilityMeasurement type SpecificationNonrecoverable read errors 1 per 1014 bits read, max.Load/Unload (L

ST1.3 Series Product Manual, Rev. D172.12 Agency certification2.12.1 Safety certificationThe drives are recognized in accordance with UL60950-1, CAN/C

18ST1.3 Series Product Manual, Rev. Dtheir compliance with our requirements by providing material content declarations for all parts and materials for

ST1.3 Series Product Manual, Rev. D19This equipment is designed to provide reasonable protection against such interference in a residential installa-t

20ST1.3 Series Product Manual, Rev. D

ST1.3 Series Product Manual, Rev. D213.0 Configuring and mounting the driveThis section contains the specifications and instructions for configuring a

22ST1.3 Series Product Manual, Rev. DFigure 8. ST1.3 Series improper handling example• Always rest the drives on a padded, antistatic surface until yo

ST1.3 Series Product Manual, Rev. D23• Handle the drive only by its edges or frame or designated finger grip region during mounting (see Figure 4).Fig

ST1.3 Series Product Manual, Rev. DiContents1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24ST1.3 Series Product Manual, Rev. D3.3 Mounting considerations• Use an elastic mounting material to protect drives so as to ensure that more shock c

ST1.3 Series Product Manual, Rev. D254.0 Interface descriptionThese drives use the industry-standard ATA task file interface that supports 16-bit data

26ST1.3 Series Product Manual, Rev. DNote. For ST1.3 Series, drive is operating in master-mode only, and the DASP# (Drive Active/SlavePresent) that is

ST1.3 Series Product Manual, Rev. D274.1.1 Supported ATA commandsThe following table lists ATA-standard commands that the drive supports. For a detail

28ST1.3 Series Product Manual, Rev. D4.1.2 Identify Device commandThe Identify Device command (command code ECH) transfers information about the drive

ST1.3 Series Product Manual, Rev. D2959 Number of sectors transferred during a Read Multiple or Write Multiple command 0100H60–61Total number of user

30ST1.3 Series Product Manual, Rev. D Note. See the bit descriptions below for words 63 and 88 of the Identify Drive data:Description (if bit is set

ST1.3 Series Product Manual, Rev. D314.1.3 Set Features commandThis command controls the implementation of various features that the drive supports. W

32ST1.3 Series Product Manual, Rev. D

ST1.3 Series Product Manual, Rev. D335.0 Seagate Technology support servicesInternetFor information regarding Seagate products and services, visit www

iiST1.3 Series Product Manual, Rev. D

34ST1.3 Series Product Manual, Rev. DCustomer Service OperationsWarranty ServiceSeagate offers worldwide customer support for Seagate products. Seagat

ST1.3 Series Product Manual, Rev. D35IndexAacoustics 15Active mode 10agency certification (regulatory) 17altitude 11ambient conditions 3ambi

36ST1.3 Series Product Manual, Rev. Dmounting the drive 21, 22Nnoise 9nominal power 3nonoperating random vibration 14nonoperating shock 1,

ST1.3 Series Product Manual, Rev. D37Zzero insertion force 1ZIF 1ZIF conn w-FPC Tab Groove 24

38ST1.3 Series Product Manual, Rev. D

Seagate Technology LLC920 Disc Drive, Scotts Valley, California 95066-4544, USAPublication Number: 100409345, Rev. D, Printed in U.S.A.

ST1.3 Series Product Manual, Rev. DiiiList of FiguresFigure 1. ST1.3 Series IDE interface (ZIF connector) disc drive . . . . . . . . . . . . . . . . .

ivST1.3 Series Product Manual, Rev. D

ST1.3 Series Product Manual, Rev. D11.0 IntroductionThis manual describes the functional, mechanical and interface specifications for the following Se

2ST1.3 Series Product Manual, Rev. D1.1 DisclaimerSeagate Technology LLC makes no warranties whatsoever, including any warranty of merchantability, no

ST1.3 Series Product Manual, Rev. D32.0 Drive specificationsUnless otherwise noted, all specifications are measured under ambient conditions, at 25°C,